Protect your TECH from electrical damage – Econnex – Compare Sim and Mobile

Protect your TECH from electrical damage

tech from electrical damage

Systems and peripherals like PCs, servers, routers and other computer devices are always at risk from electrical damages. Some examples of electrical issues are improper site wiring, fluctuations in a system’s electrical supply or lightning strikes. These issues might lead to data loss or worse unfixable systems and gadgets which you do not want to happen. We don’t know where or when these electrical issues may occur, but, we can help you to prepare your “Tech” to deal with it by precautionary measures.


Let’s define some terms that you will encounter in this article to help you understand more.


  • Multi meter(Multi tester)– use to measure voltage, current and resistance.
  • UPS(Uninterruptible Power Supply) – it is an emergency power system that provides emergency power to a load when the input power source fails.
  • Surge protector – is an appliance or device designed to protect electrical devices from a voltage spike.
  • RJ11RJ45(Registered Jack) – use to connect voice and data equipment to a service provided by a local exchange carrier.


Precautionary measures


Verify electricity levels

Usually, computers are designed to use 120 volts of AC power supplied at 60 Hertz. And, there are times your electricity company can vary from that standard so, the best thing you can do before using new systems is to check the voltage of an AC power outlet using Multimeter before you plug your device.

If baselines vary by 2% or less, use a UPS but if it varies by 3% or more, do not plug your device and contact your electricity company or licensed electrician to correct the errors as both sags and surges can lead to failures and data loss.

You call your electricity distributor to find more about this.


Confirm that the supply circuit is grounded properly

Surge protectors and UPS are designed to confirm if the electrical outlet isn’t properly grounded while Ground wiring is responsible for diverting most power surges.

Most UPS and surge protector models will light a warning lamp if the outlet isn’t properly grounded. You can buy inexpensive circuit testers that are simply plugged into outlets to confirm if the circuits are properly grounded.


Don’t overload circuits

Desktop computers, servers, and network devices connected to a single circuit can easily overpower the electrical supply. Connecting excessive amount of power upon a circuit can result in power failures, wide variations in available electricity, and even fire hazards as overworked circuits exceed safe operating ranges.


Use a UPS/surge protector

Use surge protectors and UPS devices instead of unprotected power strips as it doesn’t protect connected equipment from sags, surges and lightning strikes.

Connect all sensitive electronic devices to UPS and surge protector. Do not forget to bring a surge protector when traveling with laptops.


Remember: A laser printer’s fuse generate strong bursts of electrical consumption that can damage UPS units.


Properly calculate UPS/surge protector capacity

UPS has a power capacity as well so it’s better to carefully calculate the power needed for the systems to ensure that the UPS can power the connected equipment sufficiently. Most UPS manufacturers provide calculators for you to calculate the required power of a system.

When choosing surge protectors and consider models with a sufficient number of protected outlets. Also, ensure your surge protector has lighting protection. It will protect sensitive computer equipment from electrical spikes, resulting in failed hardware and corrupt and lost data.


Replace damaged or faulty UPS/surge protectors

Surge protector and UPS internal electronics can fail because of the continuous electrical surge. If warning lamp, outlets stop operating or batteries fail to, replace the damaged component or the entire UPS or surge protector.


Protect telecommunication links

On purchasing UPS and surge, protector, look models that protect connected devices from lightning strikes entering the network via data lines. Lightning strikes frequently discharge via cable modem, DSL, and telephone lines. It can destroy everything from network interface cards to motherboards.

Connect a corresponding RJ-11 or RJ-45 cable to the device’s protected output to guard against lightning damage on your network.


Test power supplies

Every time you encountered unexplained reboots, check the power supply’s electrical output using Multimeter to ensure that it’s working properly.

A faulty power supply should be replaced immediately to protect sensitive components such as hard disk motor, memory, video cards, and motherboards as these components can be damaged even to minor fluctuations in a system’s electrical supply.


Maintain proper operating temperatures

Protect your systems and devices against electrical damage resulting from overheating by ensuring that systems receive proper cooling, so Clean all PC’s and server exhaust fans and vents regularly and check if they are working properly. Make sure all vents, fan outlets, and UPS are free from debris, boxes, files, and other furniture so, they have ample room to breathe.

Protecting your electronic devices against electrical damage is a good investment. It will free you on paying “repairing fee”. As you well-maintain your equipment, it also increases your safeness in using them with electricity.


For more energy safety tips, visit Econnex 

1 Comment. Leave new

Leave a Reply

Your email address will not be published.

Fill out this field
Fill out this field
Please enter a valid email address.
You need to agree with the terms to proceed